Thanks for the explanation. I'll have a closer look with a magnifier...
er.. my 24/2.8 is the best "magnifier" I have around here. I'll also
consider "whittling" with some fine emery paper since the chipped
adapter seems to be unusable as is.
I don't have a problem spending more than $20. I just have a problem
spending more than $20 if the more expensive adapter doesn't fit any
better. I was just looking at the FotoDiox adapters. Unchipped cheap
ones are $20. Unchipped "Pro" models are $80. Material of the cheap
one is unspecified (possibly aluminum as some ebay models?). The
expensive one is brass, not stainless steel.
Chuck Norcutt
On 1/11/2012 11:18 PM, Moose wrote:
> On 1/11/2012 3:34 PM, Chuck Norcutt wrote:
>> No, I don't see the problem the makers have. All of these lenses fit
>> all of my OM bodies perfectly. The maker only need make the mating lens
>> flanges to the same specification as OM bodies. They're probably off by
>> 0.001-0.002 inches. A large error for a good machine shop.
>
> OK, let me revise what I said.
>
> "You can see the problem the makers have without raising the price
> considerably. The same adapter is a good fit for
> Zuikos, too tight on a Vivitar and too loose on a Tokina."
>
> Now get out your flashlight and magnifying glass. Look closely at the inside
> of the mount on an OM body. See those
> separate little springs screwed to the mount? Stainless steel mount with
> spring steel springs to hold the lens flanges.
>
> To sell an adapter for under $20 (your previous stated limit), with chip, the
> adapter is made of one solid piece of
> brass, with two screws in it, a lens stop and an aperture stop down. The
> flanges that hold the lens flanges have a kerf
> cut in them to allow them to flex and provide tension to hold the lens from
> turning.
>
> Such a design simply doesn't have the spring range to accommodate as wide a
> range of lens flange widths and depths as
> the more complex one on OM bodies. The design is nothing new. Inexpensive
> teleconverters and extension tubes from the
> old days are made the same way. The Oly teleconverters and extension tubes
> use the same, far better, but more expensive,
> design as the bodies.
>
> The focus confirmation chips used to be available separately, with a little
> jig for mounting them correctly. Perhaps you
> might separate the purchase of adapter and chips. You already have one
> adapter that fits all the lenses.
>
> As you have said you would be happy with dedicated adapter/ship combos for
> each lens, how about custom modifying
> adapters you already have? As long as the problem is that they are too tight,
> simply reduce the mating flange surfaces a
> little. You don't need a shop to sand/file/dremel/whatever each one just a
> little, test fit, repeat as necessary. Sort
> of like exposure determination by chimping. :-)
>
> My first adapter was a home made brass one with no plating. This was at the
> beginning, and all adapters were quite
> pricy. Home made and used brought down the price of the experiment of trying
> OMs on a D60 borrowed from a former list
> member before springing for a 300D. the results convinced me.
> <http://galleries.moosemystic.net/D60/> I wonder what I could do now with
> those images with such better tools and
> greater experience.
>
> The brass was a bit too soft. Worked fine with small lenses. A big, heavy one
> would soon feel loose on the camera. Twist
> a small screwdriver in the kerfs, and it would be fine until I used another
> heavy lens. I cut and stuffed tiny pieces of
> sheet aluminum into the kerfs. Worked like a charm. Still works, although I
> have other, better looking adapters now.
>
> I can just see Chuck, sitting in a rocker on the front porch of his trailer,
> whittling' away at his adapters. :-P
>
> Sittin' on the porch, retellin' old lies,
> Moose
>
--
_________________________________________________________________
Options: http://lists.thomasclausen.net/mailman/listinfo/olympus
Archives: http://lists.thomasclausen.net/mailman/private/olympus/
Themed Olympus Photo Exhibition: http://www.tope.nl/
|