Thanks!!
Pat
----- Original Message -----
From: "Piers Hemy" <piers@xxxxxxxx>
To: <olympus@xxxxxxxxxx>
Sent: Friday, April 02, 2004 11:12 AM
Subject: [OM] Re: lLight Seal
>
> Try here for John's foam instructions:
>
> http://tinyurl.com/2kqwh
>
> It's a copy of your page as it stood last May, John. I hope nothing on
that
> page has changed - and please remember that any stock lists or prices
should
> be regarded as historical mementoes!
>
> The wonders of the web archive!
>
> Piers
>
> -----Original Message-----
> From: olympus-owner@xxxxxxxxxx [mailto:olympus-owner@xxxxxxxxxx] On
Behalf
> Of John Hermanson
> Sent: 02 April 2004 17:31
> To: olympus@xxxxxxxxxx
> Subject: [OM] Re: lLight Seal
>
>
> I use the dense 2mm foam for the slots, less dense for the hinge and
mirror
> bumpers. Olympus factory foam is 2mm less dense. If it were
available, you
> could check my back foam replacement guide. Foam has get crushed to
do it's
> job.
>
> ----------------------------------------------------
> John Hermanson www.zuiko.com
> mail: omtech@xxxxxxxxx
> Camtech Photo Services, Inc.
> 21 South Lane, Huntington NY 11743-4714
> 631-424-2121 Turnaround 5-7 weeks
> ----------------------------------------------------
> ----- Original Message -----
> From: "pat rabun" <rabun@xxxxxxxx>
> To: <olympus@xxxxxxxxxx>
> Sent: Friday, April 02, 2004 9:54 AM
> Subject: [OM] Re: lLight Seal
>
>
> >
> > Thanks John. I have the dense foam from Fargo that I have used to
> > replace seals succesfully on other cameras (Olympus 35 RC, Nikon F).
Its
> > about 3mm thick. It looks like Olympus uses the less dense foam and
it
> > appears to be less than 3mm thick. Do you have any recommendations
as to
> > the thickness (depth ) of the foam? The foam by the hinge I have
already
> > replaced. Weird setup. I noticed the old foam looked kinda crushed
> > down - the new stuff looks the same. The door apparently doesn`t
close
> > squarely on the foam (by design). As long as it keeps the light
out...
> > Thanks very much. Its amazing that a busy guy like you takes time to
> > answer questions from the list. It is MUCH appreciated.
> >
> > Pat Rabun
> > OM-2, OM-2n (just getting started with Olympus after years of Nikon)
> >
> > ----- Original Message -----
> > From: "John Hermanson" <omtech@xxxxxxxxx>
> > To: <olympus@xxxxxxxxxx>
> > Sent: Friday, April 02, 2004 7:02 AM
> > Subject: [OM] Re: lLight Seal
> >
> >
> > >
> > > In the OM-1 thru 4Ti, the seals are in the slots in the body and
the
> > hinge
> > > area. ALL 1-2N (if not done recently) need them by now.
> > > ----------------------------------------------------
> > > John Hermanson www.zuiko.com
> > > mail: omtech@xxxxxxxxx
> > > Camtech Photo Services, Inc.
> > > 21 South Lane, Huntington NY 11743-4714
> > > 631-424-2121 Turnaround 5-7 weeks
> > > ----------------------------------------------------
> > > ----- Original Message -----
> > > From: "pat rabun" <rabun@xxxxxxxx>
> > > To: <olympus@xxxxxxxxxx>
> > > Sent: Thursday, April 01, 2004 3:57 PM
> > > Subject: [OM] lLight Seal
> > >
> > >
> > > >
> > > > Silly question: Are the light seals for the OM-2 and OM-2n on
the
> > body
> > > > of the camera or on the door? I am thinking the body- there is a
> > large
> > > > seal on the right side of the body by the hinge. The others
appear
> > to
> > > > run in small channels horizontally on the body. Thanks.
> > > >
> > > > Pat Rabun
> > > >
> > > >
> > >
> > >
> > >
>
>
>
> The olympus mailinglist olympus@xxxxxxxxxx
> To unsubscribe: mailto:olympus-request@xxxxxxxxxx?subject=unsubscribe
>
> To contact the list admins:
mailto:olympusadmin@xxxxxxxxxx?subject="Olympus
> List Problem"
>
>
> The olympus mailinglist olympus@xxxxxxxxxx
> To unsubscribe: mailto:olympus-request@xxxxxxxxxx?subject=unsubscribe
>
> To contact the list admins:
mailto:olympusadmin@xxxxxxxxxx?subject="Olympus List Problem"
>
The olympus mailinglist olympus@xxxxxxxxxx
To unsubscribe: mailto:olympus-request@xxxxxxxxxx?subject=unsubscribe
To contact the list admins: mailto:olympusadmin@xxxxxxxxxx?subject="Olympus
List Problem"
|